Smun Lrs-100-24 100W 24VDC 4.2A Slim Economical Switching Power Supply SMPS

Product Description

 

Model		LRS-100-5	LRS-100-12	LRS-100-15	LRS-100-24	LRS-100-36	LRS-100-48
output	DC voltage	5V	12V	15V	24V	36V	48V
	Rated current	18A	8.5A	7A	4.5A	2.8A	2.3A
	Current range	0~18A	0~8.5A	0~7A	0~4.5A	0~2.8A	0~2.3A
	Rated power	90W	102W	105W	108W	100.8W	110.4W
	Ripple&noise	100mVp-p	120mVp-p	120mVp-p	150mVp-p	200mVp-p	200mVp-p
	DC voltage ADJ. range	±10%	±10%	±10%	±10%	±10%	±10%
	Voltage tolerance Note.3	±3%	±2%	±1%	±1%	±1%	±1%
	Line regulation Note.4	±0.5%	±0.5%	±0.5%	±0.5%	±0.5%	±0.5%
	Load regulation Note.5	±2%	±1%	±0.5%	±0.5%	±0.5%	±0.5%
	Setup,rise,hold up time	800ms,30ms,55ms/230VAC(full load)
input	Voltage range	90~264VAC,127~373VDC
	Frequency range	47~63HZ
	AC current	1.9A/115VAC     1.2A/230VAC
	Inrush current	Cold start 50A/230VAC
	Efficiency	86%	88%	88.5%	90%	90.5%	91%
	Leakage current	<0.75mA/240VAC
protection	overload	Rated output power110%~150%  start over load protection
		protection type:hiccup mode,auto-recovery after fault condition is removed
	Over voltage	Rated output voltage 115%~135% Start over voltage protection
		Protection type:hiccup mode,auto-recovery after fault condition is removed
environment	Working temp,humidity	-30ºC~+70ºC(Please refer to"derating curve") 20%~90%RH Non-condensing
	Storage temp,humidity	-40ºC~+85ºC,10%~95%RH non-condensing
	Withstand vibration	10~500HZ,2G 10min/1cycle,period for 60 minutes,each axes
safety	Withstand voltage	I/P-O/P:1.5KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
	Isolation resistance	I/P-O/P,I/P-FG,O/P-FG:100M ohms/500VDC
Fit standard	Safety standards	Compliance to UL60950-1,TUV EN60950-1,GB4943
	EMC emission	Compliance to EN55022(CISPR22)Class A,GB9254 Class B,EN55014,EN61000-3-2,3
	EMC immunity	Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024,EN61000-6-1
others	Dimension	129*97*30mm(L*W*H)
	Weight/packing	0.34kg/40pcs/14.6kg/0.025m³/0.88CUFT
	MTBF	≥705K hrs min. MIL-HDBK-217F(25ºC)
note	1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25ºC of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4.Line regulation is measured from low line to high line at rated load. 5.Load regulation is measured from 0% to 100% rated load 6.The ambient temperature derating of 5ºC/1000 m is needed for operating altitude greater than 2000m(6500ft) 7.The power supply is considered as a component which will be installed into a finalequipment.The final equipment must be re-confirmed that it still meets EMC directives.For guidance on how to perform these EMC tests.